LED Street Light

Product Details:

1.0.0 SPECIFICATIONS.1.1.0 GENERAL:1.1.1. SCOPE : This Specification defines the performance characteristics of 90WAC - DC LED Street Light Driver.1.2.0 INPUT CHARACTERISTIC:1.2.1. INPUT OPERATING VOLTAGE : 140VAC-300VAC.1.2.2. INPUT FREQUENCY : 47Hz to 63Hz.1.2.3. INPUT CURRENT : <800mA RMS @ 140VAC.1.2.4. INPUT WATTAGE : 90W ± 5%.1.2.5. EFFICIENCY : >85% @ 230VAC.1.2.6. POWER FACTOR : >0.90 @ 230VAC.1.2.7. THDi : <10% @ 230VAC.1.3.0 OUTPUT CHARACTERISTIC:1.3.1.OUTPUT VOLTAGE : 68V - 75VDC.1.3.2. OUTPUT CURRENT : 1.15A ± 50mA Constant Current.1.3.3. LINE & LOAD REGULATION : ± 5%.1.4.0 PROTECTIONS:1.4.1. OVER TEMPERATURE : The driver is protected against over temperature. when the junctionPROTECTION temperature on the driver chip die rises to 150ºC, the driver willshutdown immediately and will remain switched off until thetemperature on die falls to 130ºC.1.4.2. OUTPUT OVERLOAD/ : The driver is protected against over load & short circuit .SHORT CIRCUIT PROTECTION During over load & Short circuit the driver will go to hick upmode and resumes to normal operation on removal of fault condition.SPECIFICATIONSDOC.No. TEP / SPEC / 802 / 00 Page 2 of 3MODEL NO.: 90W Street Light Driver.1.4.3. OUTPUT OVER VOLTAGE : In case of output load open the driver output will limit the voltage toPROTECTION safe levels and will work normally when the load is connected back.this will not create any hard failures in the driver.1.4.4. INPUT HIGH VOLTAGE : The driver is protected against input high voltage so it can withstandPROTECTION up to 440VAC supply.1.5.0 ENVIRONMENT:1.5.1. TEMPERATURE : Operating Ambient 0ºC to + 50ºC.: Storage -15ºC to +70ºC ambient.1.5.2. HUMIDITY : Operating 5% RH to 95% RH non - condensing.: Storage 5% RH to 95% RH non- condensing.1.6.0 PRODUCT SAFETY:1.6.1. DI-ELECTRIC VOLTAGE : 1.5KVAC RMS, 50Hz for one minute (trip current set at 5mA)WITHSTAND TEST Between Shorted Input and Output terminals.1.7.0 SURGE PROTECTION: : 6KV Differential mode.1.8.0 TERMINATIONS:1.8.1. AC INPUT : 3Core, 0.30Mtr Length open Wires.1.8.2. DC OUTPUT : 2Core, 0.20Mtr Length open Wires.1.9.0 MECHANICAL:1.9.1. DRIVER DIMENSIONS : Length: 121.00mm, Width: 76.00mm, Height: 41.00mm.

Product Details:

This Specification defines the performance characteristics of 15WLED Street Light.1.2.0 INPUT CHARACTERISTIC:1.2.1. INPUT OPERATING VOLTAGE : 140VAC-300VAC (Withstand Voltage up to 350VAC)1.2.2. INPUT POWER : 15W ± 5%.1.2.3. INPUT FREQUENCY : 47Hz to 63Hz.1.2.4. INPUT CURRENT : <150mA RMS @140VAC.1.2.5. EFFICIENCY : >85% @ 230VAC.1.2.6. POWER FACTOR : >0.90 @ 230VAC.1.2.7. THDi. : <15% @ 230VAC.1.2.8. LUMEN OUTPUT : >1125 lm.1.2.9. LUMEN EFFICIENCY : >75 lm/W.1.2.10. CCT : 6000K - 6500K.1.3.0 OUTPUT CHARACTERISTIC:1.3.1.OUTPUT VOLTAGE : 67V - 72VDC.1.3.2. OUTPUT CURRENT : 200mA ± 30mA Constant Current.1.3.3. LINE & LOAD REGULATION : ± 5%.1.4.0 PROTECTIONS:1.4.1. OVER TEMPERATURE : The light is protected against over temperature. when the junctionPROTECTION temperature on the driver chip die rises to 150ºC, the light willshutdown immediately and will remain switched off until thetemperature on die falls to 130ºC.1.4.2. OUTPUT OVERLOAD/ : The light is protected against over load & short circuit .SHORT CIRCUIT PROTECTION During over load & Short circuit the driver will go to hick upmode and resumes to normal operation on removal of fault condition.SPECIFICATIONS AXIOM POWER PRODUCTS PVT. LTD.DOC.No. TEP / SPEC / 127 / 00 Page 2 of 3MODEL NO.: SLNCAHF015 (15W Street light).1.4.3. OUTPUT OVER VOLTAGE : In case of output load open the driver output will limit the voltage toPROTECTION safe levels and will work normally when the load is connected back.this will not create any hard failures in the driver.1.5.0 ENVIRONMENT:1.5.1. TEMPERATURE : Operating Ambient 0ºC to + 50ºC.: Storage -15ºC to +70ºC ambient.1.5.2. HUMIDITY : Operating 5% RH to 95% RH non - condensing.: Storage 5% RH to 95% RH non- condensing.1.6.0 DIMENSIONS : Length: 350.0mm, Width: 95.00mm, Height: 65.00mm.

Product Details:

This Specification defines the performance characteristics of 24WLED Street Light.1.2.0 INPUT CHARACTERISTIC:1.2.1. INPUT OPERATING VOLTAGE : 140VAC-300VAC (Withstand Voltage up to 350VAC)1.2.2. INPUT POWER : 24W ± 5%.1.2.3. INPUT FREQUENCY : 47Hz to 63Hz.1.2.4. INPUT CURRENT : <250mA RMS @140VAC.1.2.5. EFFICIENCY : >85% @ 230VAC.1.2.6. POWER FACTOR : >0.90 @ 230VAC.1.2.7. THDi. : <15% @ 230VAC.1.2.8. LUMEN OUTPUT : >1800 lm.1.2.9. LUMEN EFFICIENCY : >75 lm/W.1.2.10. CCT : 6000K - 6500K.1.3.0 OUTPUT CHARACTERISTIC:1.3.1.OUTPUT VOLTAGE : 67V - 72VDC.1.3.2. OUTPUT CURRENT : 300mA ± 50mA Constant Current.1.3.3. LINE & LOAD REGULATION : ± 5%.1.4.0 PROTECTIONS:1.4.1. OVER TEMPERATURE : The light is protected against over temperature. when the junctionPROTECTION temperature on the driver chip die rises to 150ºC, the light willshutdown immediately and will remain switched off until thetemperature on die falls to 130ºC.1.4.2. OUTPUT OVERLOAD/ : The light is protected against over load & short circuit .SHORT CIRCUIT PROTECTION During over load & Short circuit the driver will go to hick upmode and resumes to normal operation on removal of fault condition.SPECIFICATIONS AXIOM POWER PRODUCTS PVT. LTD.DOC.No. TEP / SPEC / 128 / 00 Page 2 of 3MODEL NO.: SLNCAHF024 (24W Street light).1.4.3. OUTPUT OVER VOLTAGE : In case of output load open the driver output will limit the voltage toPROTECTION safe levels and will work normally when the load is connected back.this will not create any hard failures in the driver.1.5.0 ENVIRONMENT:1.5.1. TEMPERATURE : Operating Ambient 0ºC to + 50ºC.: Storage -15ºC to +70ºC ambient.1.5.2. HUMIDITY : Operating 5% RH to 95% RH non - condensing.: Storage 5% RH to 95% RH non- condensing.1.6.0 DIMENSIONS : Length: 350.0mm, Width: 95.00mm, Height: 65.00mm.

Product Details:

MODEL NO.: SLNCAHF036 (36W Street light).This Specification defines the performance characteristics of 36WLED Street Light.1.2.0 INPUT CHARACTERISTIC:1.2.1. INPUT OPERATING VOLTAGE : 140VAC-300VAC (Withstand Voltage Up to 350VAC).1.2.2. INPUT POWER : 36W ± 5%.1.2.3. INPUT FREQUENCY : 47Hz to 63Hz.1.2.4. INPUT CURRENT : <400mA RMS @140VAC.1.2.5. EFFICIENCY : >85% @ 230VAC.1.2.6. POWER FACTOR : >0.90 @ 230VAC.1.2.7. THDi. : <15% @ 230VAC.1.2.8. LUMEN OUTPUT : >2900lm.1.2.9. LUMEN EFFICIENCY : >80lm/W.1.2.10. CCT : 6000-6500K.1.3.0 OUTPUT CHARACTERISTIC:1.3.1.OUTPUT VOLTAGE : 67V - 72VDC (Dual Output).1.3.2. OUTPUT CURRENT : 250mA ± 30mA Constant Current (Dual Output).1.3.3. LINE & LOAD REGULATION : ± 5%.1.4.0 PROTECTIONS:1.4.1. OVER TEMPERATURE : The light is protected against over temperature. when the junctionPROTECTION temperature on the driver chip die rises to 150ºC, the light willshutdown immediately and will remain switched off until thetemperature on die falls to 130ºC.1.4.2. OUTPUT OVERLOAD/ : The light is protected against over load & short circuit .SHORT CIRCUIT PROTECTION During over load & Short circuit the driver will go to hick upmode and resumes to normal operation on removal of fault condition.SPECIFICATIONS AXIOM POWER PRODUCTS PVT. LTD.DOC.No. TEP / SPEC / 129 / 00 Page 2 of 3MODEL NO.: SLNCAHF036 (36W Street light).1.4.3. OUTPUT OVER VOLTAGE : In case of output load open the driver output will limit the voltage toPROTECTION safe levels and will work normally when the load is connected back.this will not create any hard failures in the driver.1.5.0 ENVIRONMENT:1.5.1. TEMPERATURE : Operating Ambient 0ºC to + 50ºC.: Storage -15ºC to +70ºC ambient.1.5.2. HUMIDITY : Operating 5% RH to 95% RH non - condensing.: Storage 5% RH to 95% RH non- condensing.1.6.0 DIMENSIONS : Length: 385.00mm, Width: 145.00mm, Height: 60.00mm.

Product Details:

This Specification defines the performance characteristics of 48WAC-DC LED Street Light.1.2.0 INPUT CHARACTERISTIC:1.2.1. INPUT OPERATING VOLTAGE : 140VAC-300VAC.1.2.2. INPUT FREQUENCY : 47Hz to 63Hz.1.2.3. INPUT CURRENT : <400mA RMS @ 140VAC.1.2.4. INPUT WATTAGE : 48W ± 5%.1.2.5. EFFICIENCY : >84% @ 230VAC.1.2.6. POWER FACTOR : >0.90 @ 230VAC.1.2.7. THDi : <10% @ 230VAC.1.2.8. LUMEN OUTPUT : >4560lm.1.2.9. LUMEN EFFICIENCY : >95lm/W.1.2.10. CCT : 6000K - 6500K.1.3.0 OUTPUT CHARACTERISTIC:1.3.1.OUTPUT VOLTAGE : 68V - 75VDC.1.3.2. OUTPUT CURRENT : 600mA ± 50mA Constant Current.1.3.3. LINE & LOAD REGULATION : ± 5%.1.4.0 PROTECTIONS:1.4.1. OVER TEMPERATURE : The driver is protected against over temperature. when the junctionPROTECTION temperature on the driver chip die rises to 150ºC, the light willshutdown immediately and will remain switched off until thetemperature on die falls to 130ºC.1.4.2. OUTPUT OVERLOAD/ : The driver is protected against over load & short circuit .SHORT CIRCUIT PROTECTION During over load & Short circuit the light will go to hick upmode and resumes to normal operation on removal of fault condition.SPECIFICATIONSDOC.No. TEP / SPEC / 268 / 00 Page 2 of 3MODEL NO.: SLICANB048 (48W STREET LIGHT).1.4.3. OUTPUT OVER VOLTAGE : In case of output load open the driver output will limit the voltage toPROTECTION safe levels and will work normally when the load is connected back.this will not create any hard failures in the driver.1.5.0 ENVIRONMENT:1.5.1. TEMPERATURE : Operating Ambient 0ºC to + 50ºC.: Storage -15ºC to +70ºC ambient.1.5.2. HUMIDITY : Operating 5% RH to 95% RH non - condensing.: Storage 5% RH to 95% RH non- condensing.1.6.0 PRODUCT SAFETY:1.6.1. DI-ELECTRIC VOLTAGE : 1.5KVAC RMS, 50Hz for one minute (trip current set at 5mA)WITHSTAND TEST Between Shorted Input and Output terminals.1.7.0 SURGE PROTECTION: : 6KV Differential mode.1.8.0 TERMINATIONS:1.8.1. AC INPUT : 3Core, 0.20Mtr Length open Wires..1.9.0 MECHANICAL:1.9.1. CASING DIMENSIONS : Length: 405.00mm, Width: 195.00mm, Height: 70.00mm.

Product Details:

MODEL NO.: SLICAMB072 (72W STREET LIGHT).This Specification defines the performance characteristics of 72WAC-DC LED Street Light.1.2.0 INPUT CHARACTERISTIC:1.2.1. INPUT OPERATING VOLTAGE : 140VAC-300VAC.1.2.2. INPUT FREQUENCY : 47Hz to 63Hz.1.2.3. INPUT CURRENT : <600mA RMS @ 140VAC.1.2.4. INPUT WATTAGE : 72W ± 5%.1.2.5. EFFICIENCY : >80% @ 230VAC.1.2.6. POWER FACTOR : >0.90 @ 230VAC.1.2.7. THDi : <15% @ 230VAC.1.2.8. LUMEN OUTPUT : >5400lm.1.2.9. LUMEN EFFICIENCY : >75lm/W.1.2.10. CCT : 6000K - 6500K.1.3.0 OUTPUT CHARACTERISTIC:1.3.1.OUTPUT VOLTAGE : 100V - 108VDC.1.3.2. OUTPUT CURRENT : 650mA ± 50mA Constant Current.1.3.3. LINE & LOAD REGULATION : ± 5%.1.4.0 PROTECTIONS:1.4.1. OVER TEMPERATURE : The driver is protected against over temperature. when the junctionPROTECTION temperature on the driver chip die rises to 150ºC, the light willshutdown immediately and will remain switched off until thetemperature on die falls to 130ºC.1.4.2. OUTPUT OVERLOAD/ : The driver is protected against over load & short circuit .SHORT CIRCUIT PROTECTION During over load & Short circuit the light will go to hick upmode and resumes to normal operation on removal of fault condition.SPECIFICATIONSDOC.No. TEP / SPEC / 258 / 00 Page 2 of 3MODEL NO.: SLICAMB072 (72W STREET LIGHT).1.4.3. OUTPUT OVER VOLTAGE : In case of output load open the driver output will limit the voltage toPROTECTION safe levels and will work normally when the load is connected back.this will not create any hard failures in the driver.1.4.4. INPUT HIGH VOLTAGE : The light is protected against input high voltage so it can withstandPROTECTION up to 440VAC supply.1.5.0 ENVIRONMENT:1.5.1. TEMPERATURE : Operating Ambient 0ºC to + 50ºC.: Storage -15ºC to +70ºC ambient.1.5.2. HUMIDITY : Operating 5% RH to 95% RH non - condensing.: Storage 5% RH to 95% RH non- condensing.1.6.0 PRODUCT SAFETY:1.6.1. DI-ELECTRIC VOLTAGE : 1.5KVAC RMS, 50Hz for one minute (trip current set at 5mA)WITHSTAND TEST Between Shorted Input and Output terminals.1.7.0 SURGE PROTECTION: : 5KV Differential mode.1.8.0 TERMINATIONS:1.8.1. AC INPUT : 3Core, 0.20Mtr Length open Wires..1.9.0 MECHANICAL:1.9.1. CASING DIMENSIONS : Length: 430.00mm, Width: 205.00mm, Height: 75.00mm.

Product Details:

MODEL NO.: SLICBNB160 (160W STREET LIGHT).This Specification defines the performance characteristics of 160WAC-DC LED Street Light.1.2.0 INPUT CHARACTERISTIC:1.2.1. INPUT OPERATING VOLTAGE : 140VAC-300VAC.1.2.2. INPUT FREQUENCY : 47Hz to 63Hz.1.2.3. INPUT CURRENT : <1.40A RMS @ 140VAC.1.2.4. INPUT WATTAGE : 160W ± 5%.1.2.5. EFFICIENCY : >85% @ 230VAC.1.2.6. POWER FACTOR : >0.90 @ 230VAC.1.2.7. THDi : <10% @ 230VAC.1.2.8. LUMEN OUTPUT : >12000lm.1.2.9. LUMEN EFFICIENCY : >75lm/W.1.2.10. CCT : 6000K - 6500K.1.3.0 OUTPUT CHARACTERISTIC:1.3.1.OUTPUT VOLTAGE : 80V - 88VDC (Dual Output).1.3.2. OUTPUT CURRENT : 800mA ± 50mA Constant Current (Dual Output).1.3.3. LINE & LOAD REGULATION : ± 5%.1.4.0 PROTECTIONS:1.4.1. OVER TEMPERATURE : The driver is protected against over temperature. when the junctionPROTECTION temperature on the driver chip die rises to 150ºC, the light willshutdown immediately and will remain switched off until thetemperature on die falls to 130ºC.1.4.2. OUTPUT OVERLOAD/ : The driver is protected against over load & short circuit .SHORT CIRCUIT PROTECTION During over load & Short circuit the light will go to hick upmode and resumes to normal operation on removal of fault condition.SPECIFICATIONSDOC.No. TEP / SPEC / 133 / 00 Page 2 of 3MODEL NO.: SLICBNB160 (160W STREET LIGHT).1.4.3. OUTPUT OVER VOLTAGE : In case of output load open the driver output will limit the voltage toPROTECTION safe levels and will work normally when the load is connected back.this will not create any hard failures in the driver.1.4.4. INPUT HIGH VOLTAGE : The light is protected against input high voltage so it can withstandPROTECTION up to 440VAC supply.1.5.0 ENVIRONMENT:1.5.1. TEMPERATURE : Operating Ambient 0ºC to + 50ºC.: Storage -15ºC to +70ºC ambient.1.5.2. HUMIDITY : Operating 5% RH to 95% RH non - condensing.: Storage 5% RH to 95% RH non- condensing.1.6.0 PRODUCT SAFETY:1.6.1. DI-ELECTRIC VOLTAGE : 1.5KVAC RMS, 50Hz for one minute (trip current set at 5mA)WITHSTAND TEST Between Shorted Input and Output terminals.1.7.0 SURGE PROTECTION: : 6KV Differential mode.1.8.0 TERMINATIONS:1.8.1. AC INPUT : 3Core, 0.20Mtr Length open Wires..1.9.0 MECHANICAL:1.9.1. CASING DIMENSIONS : Length: 510.00mm, Width: 260.00mm, Height: 75.00mm.

Product Details:

SPECIFICATIONS:-This Specification defines the performance characteristics of 60WAC-DC LED Street Light.INPUT CHARACTERISTIC:INPUT OPERATING VOLTAGE : 140VAC-300VAC.INPUT FREQUENCY : 47Hz to 63Hz.INPUT CURRENT : <500mA RMS @ 140VAC.INPUT WATTAGE : 60W ± 5%.EFFICIENCY : >85% @ 230VAC.POWER FACTOR : >0.95 @ 230VAC.THDi : <10% @ 230VAC.LUMEN OUTPUT : >5700lm.LUMEN EFFICIENCY : >95lm/W.CCT : 6000K - 6500K.OUTPUT CHARACTERISTIC:OUTPUT VOLTAGE : 68V - 75VDC.OUTPUT CURRENT : 750mA ± 50mA Constant Current.LINE & LOAD REGULATION : ± 5%.PROTECTIONS:OVER TEMPERATURE : The light is protected against over temperature. when the junctionPROTECTION temperature on the driver chip die rises to 150ºC, the light willshutdown immediately and will remain switched off until thetemperature on die falls to 130ºC.OUTPUT OVERLOAD/ : The light is protected against over load & short circuit .SHORT CIRCUIT PROTECTION During over load & Short circuit the light will go to hick upmode and resumes to normal operation on removal of fault condition.OUTPUT OVER VOLTAGE : In case of output load open the driver output will limit the voltage toPROTECTION safe levels and will work normally when the load is connected back.this will not create any hard failures in the driver.ENVIRONMENT:TEMPERATURE : Operating Ambient 0ºC to + 50ºC.: Storage -15ºC to +70ºC ambient.1.5.2. HUMIDITY : Operating 5% RH to 95% RH non - condensing.: Storage 5% RH to 95% RH non- condensing.PRODUCT SAFETY: DI-ELECTRIC VOLTAGE : 1.5KVAC RMS, 50Hz for one minute (trip current set at 5mA)WITHSTAND TEST Between Shorted Input and Output terminals.SURGE PROTECTION: : 6KV Differential mode. TERMINATIONS:AC INPUT : 3Core, 0.20Mtr Length open Wires..MECHANICAL:CASING DIMENSIONS : Length: 405.00mm, Width: 195.00mm, Height: 70.00mm.

Product Details:

This Specification defines the performance characteristics of 120WAC - DC LED Street Light Driver.1.2.0 INPUT CHARACTERISTIC:1.2.1. INPUT OPERATING VOLTAGE : 140VAC-300VAC.1.2.2. INPUT FREQUENCY : 47Hz to 63Hz.1.2.3. INPUT CURRENT : <1.0A RMS @ 140VAC.1.2.4. INPUT WATTAGE : 120W ± 5%.1.2.5. EFFICIENCY : >85% @ 230VAC.1.2.6. POWER FACTOR : >0.90 @ 230VAC.1.2.7. THDi : <10% @ 230VAC.1.3.0 OUTPUT CHARACTERISTIC:1.3.1.OUTPUT VOLTAGE : 32V - 38VDC.1.3.2. OUTPUT CURRENT : 2.90A ± 100mA Constant Current.1.3.3. LINE & LOAD REGULATION : ± 5%.1.4.0 PROTECTIONS:1.4.1. OVER TEMPERATURE : The driver is protected against over temperature. when the junctionPROTECTION temperature on the driver chip die rises to 150ºC, the driver willshutdown immediately and will remain switched off until thetemperature on die falls to 130ºC.1.4.2. OUTPUT OVERLOAD/ : The driver is protected against over load & short circuit .SHORT CIRCUIT PROTECTION during over load & Short circuit the driver will go to hick upmode and resumes to normal operation on removal of fault condition.SPECIFICATIONSDOC.No. TEP / SPEC / 803 / 00 Page 2 of 3MODEL NO.: 120W Street Light Driver.1.4.3. OUTPUT OVER VOLTAGE : In case of output load open the driver output will limit the voltage toPROTECTION safe levels and will work normally when the load is connected back.this will not create any hard failures in the driver.1.4.4. INPUT HIGH VOLTAGE : The light is protected against input high voltage so it can withstandPROTECTION up to 440VAC supply.1.5.0 ENVIRONMENT:1.5.1. TEMPERATURE : Operating Ambient 0ºC to + 50ºC.: Storage -15ºC to +70ºC ambient.1.5.2. HUMIDITY : Operating 5% RH to 95% RH non - condensing.: Storage 5% RH to 95% RH non- condensing.1.6.0 PRODUCT SAFETY:1.6.1. DI-ELECTRIC VOLTAGE : 1.5KVAC RMS, 50Hz for one minute (trip current set at 5mA)WITHSTAND TEST Between Shorted Input and Output terminals.1.7.0 SURGE PROTECTION: : 6KV Differential mode.1.8.0 TERMINATIONS:1.8.1. AC INPUT : 3Core, 0.30Mtr Length open Wires.1.8.2. DC OUTPUT : 2Core, 0.20Mtr Length open Wires.1.9.0 MECHANICAL:1.9.1. DRIVER DIMENSIONS : Length: 148.00mm, Width: 89.00mm, Height: 48.00mm.